GuidesBy Taxidermy Hobbyist Editorial TeamUpdated November 22, 2026

How to Tan a Rabbit Hide or Pelt at Home

Why is a rabbit hide harder to tan than a deer hide?

Learning how to tan a rabbit hide is mostly learning to handle a skin that tears if you look at it wrong. The chemistry is simple: salt, alum and water. The hard part is fleshing, stirring and softening a skin so thin that the tools and force you'd use on a deer would rip it apart.

Outdoor Life writer Beka Garris, who has tanned deer, fox, coyote and mink, calls cottontail hides the "tissue paper" of furbearing animals and says a fleshing tool would destroy the thin skin (Outdoor Life). Hide tanner Woniya of Timeless Ways calls rabbit "quite thin and not a very strong hide", and notes that fur holds moisture, so a fur-on skin dries slower and needs more working (video, 2022). For the general process, see our overview of tanning hides at home, then come back here for the rabbit-specific handling.

How do you skin and store a rabbit pelt before tanning?

Skin the rabbit cased: cut around the hind legs and pull the skin down over the body like a sleeve, leaving a tube. Rinse off blood in cold water, skip the scraping for now, and either start tanning the same day or freeze the pelt in a bag for up to about a year.

Mississippi State University Extension describes the cased method: cut the skin around the hock joints, join those cuts across the lower body, take off the tail and peel the skin forward and down over the body. It notes that skins of young fryer rabbits come off easily and older rabbits are harder (MSU Extension). Speed matters with any fur: New Mexico State University warns that in warm weather hair can start to slip within an hour after death, especially in direct sun, so skin as soon as you can (NMSU Guide L-101).

Countryside's guide says to rinse the blood off in cold water right away, leave the fat and flesh for later, because "too much mishandling can poke holes in the pelts", and to freeze the pelt with the air pressed out for up to a year (Countryside). If you'd rather dry skins, MSU Extension's method for pelts kept for sale turns them inside out while warm, puts them on wire shapers, and hangs them in a ventilated spot out of direct sun. Don't let a raw pelt dry out before you tan it: one Permies member who salted a pelt heavily and let it dry found it "stiff as a board", and another member in the same thread advised using "a fresh hide, not a dried hide" and salting the flesh side overnight "but not dry out" (Permies, 2014).

Which tan should you use on a rabbit skin?

For a first rabbit, use a salt-alum soak. It needs only non-iodized salt, alum and water, and it's the method the Countryside, Mother Earth News and Cast Blast Camp rabbit guides use. Acid pickles and commercial kits work too, but the Van Dyke's directions below are written for whitetail capes.

MSU Extension gives a salt-alum method and a salt-acid method, and calls the alum method "slightly better" but says it usually leaves a harder skin that needs more working. Its acid method uses concentrated sulfuric acid, which MSU says "is very corrosive and must be handled with care", so this page doesn't give it as a home recipe. Van Dyke's calls potassium alum "an excellent tan for skins from rabbit to deer" (Van Dyke's).

If you already own a cape pickle, Van Dyke's directions for McKenzie Ultimate Acid call for 1 pound of non-iodized salt and 1/2 fluid ounce of acid in each gallon of water, with the pH held between 1.0 and 2.0 and a 3 day pickle for a cape (Van Dyke's). There are also methods without alum or acid: Garris soap-tanned a cottontail with olive oil and dish soap in about an hour plus drying, and egg-yolk and smoke methods are covered in our guide to brain and smoke tanning.

How do you tan a rabbit hide with salt and alum?

Soak the pelt, skin side out, in a salt and alum brine for a few days, peel off the loosened flesh by hand, return it to a refreshed brine for about another week, then rinse, wash and dry it while you stretch it soft. Stir twice a day the whole time. These steps follow the Countryside guide.

  1. Mix the brine. In a plastic tub with a lid, dissolve 1 cup non-iodized salt and 1 cup alum in 2 gallons of lukewarm water. Countryside says that batch tans five large or ten small pelts. For a single hide, a Cast Blast Camp video uses 1/4 cup salt and 1/4 cup alum in a half-gallon mason jar (video, 2025).
  2. Submerge the pelts. Thaw frozen hides. Keep a tube hide fur side in, skin side out, weigh it down, and cover the tub.
  3. Soak and stir. Countryside says to leave the pelts at room temperature for a minimum of two days and under a week, stirring a couple of times a day.
  4. Flesh by hand. Squeeze (never wring) the brine back into the tub and keep it. Starting at the hind-leg end, loosen the membrane with your fingernails or a serrated knife, then pull it slowly toward the neck. If it won't release, soak a couple more days. If you must use a knife, keep the blade flat to the skin.
  5. Refresh the brine. Add another cup each of salt and alum, stir until dissolved, and return the hides inside out.
  6. Tan. Soak at least one more week, still stirring at least twice a day.
  7. Test. Cut a small scrap from an edge and drop it in boiling water. If it curls and hardens, it's not done. If it stays soft, move on.
  8. Rinse and wash. Rinse in lukewarm water, turn fur side out, rinse again, then work a little shampoo or soap into the fur and rinse it all out.
  9. Dry and break. Hang the pelt to drip dry, and soften it before it dries completely (next sections).
  10. Oil. Rub a little mink oil into the skin side. Countryside says "a little mink oil goes a long way". MSU Extension uses neat's-foot oil, glycerin or another leather conditioner.

Melissa Souza, who raises meat rabbits and wrote a reader contribution for Mother Earth News, warns that the edges "can tear easily" and "the younger the rabbit the more fragile the pelt" (Mother Earth News). In the Cast Blast Camp video, hand fleshing one hide took "a few hours", with tweezers and a razor blade for stubborn spots. Halford Homestead takes the other route: a dull fleshing knife over a beam made from sewer pipe, before any soak, because pickling first and peeling by hand "takes forever". He warns that the nipples on a doe can pop or rip (video, 2023).

None of the rabbit guides cited here includes a shaving step, the thinning you may do on a deer hide.

How long does each step take for a small skin?

Plan on about two to three weeks from thawed pelt to soft fur with the two-soak salt-alum method; Souza says her batches take around three weeks. Fleshing can take a few hours per hide, and drying and breaking take one to three days. The table shows what each source reports.

StepTime reportedSource
First brine soakAt least 2 days, less than a weekCountryside
First brine soak5 to 7 daysMother Earth News (Souza)
Hand fleshing, one hideA few hours (one hunted rabbit); 1.5 hours each (3 year old breeders)Cast Blast Camp video; one Permies member, 2018
Second brine soakAt least 1 week; 7 to 14 daysCountryside; Mother Earth News
Soak tan, no paste2 to 4 daysMSU Extension
Drying and stretching2 to 3 days; about 24 hours to dry a soap-tanned hideCast Blast Camp video; Outdoor Life
Whole process, batchAbout 3 weeksMother Earth News (Souza)

How do you soften a rabbit pelt as it dries?

Work the skin while it's still slightly damp: pull it gently in every direction, a small section at a time, until it turns from dark to white and dries soft. If a spot dries stiff, re-wet it with a damp cloth and work it again. Pulling hard will tear it.

Countryside says to slit the tube open, then pull horizontally, vertically and diagonally as the skin turns "from black or olive-oil-colored to a bright white", taking care at the bottom "because it tears easiest there". Souza stretches when the hides are "mostly dry," but not stiff, and re-wets with a damp cloth if they go too far. MSU Extension works a nearly dry skin over the edge of a table, "as in polishing shoes with a cloth", and says you may need to resoak, partly dry and rub again. In the Cast Blast Camp video, working the skin with a spoon helps break down the fibers as the pelt dries.

How do you know it's dry? Woniya says a damp hide feels cool to the touch and a dry one feels warm, and one Permies member says to keep working until the skin side "feels warm to the touch". A stiff pelt isn't a lost cause. In a 2018 Permies thread, a member's fleshed and pickled pelts from three-year-old breeders dried "tough like rawhide" in parts; the reply said the tanner "stopped working it too soon" and only needed to wet the stiff areas again and work them a second time.

Stretching isn't universal. Garris writes that "trying to stretch a rabbit hide just rips it in half" and softened her soap-tanned cottontail by folding it and rolling it up into a ball.

Why does rabbit fur slip or fall out?

Rabbit fur slips when part of the skin spoils or never tans: the hide warmed before skinning, a fold never touched the brine, it soaked too long in plain water, or, one tanner warns, the solution was too weak. Fast skinning, fully submerged pelts and stirring twice a day help prevent it.

  • Folds that never tanned. Countryside and Souza both say that failing to stir twice a day causes hair slip and bald patches where folded skin didn't contact the brine.
  • Temperature, salt and submersion. Countryside says to use non-iodized salt, keep the water at room temperature, "never above 80 and never below 55", and keep every part of the hide submerged "so they don't decay".
  • Over-soaking. MSU Extension keeps rehydrating soaks for dried skins short, about 1 to 3 hours, "since excessive soaking tends to loosen the hair".
  • A weak solution. One member of a New Zealand hunting forum, describing the bark tans he prefers, advises keeping the mix "a little acidic and the solution strong" to avoid slip, then rinsing and neutralizing at the end (NZ Hunting and Shooting, 2017).
  • Cutting through fur. The Cast Blast Camp video opens the belly with a blade through the skin only, because scissors "can cause more hair to fall out".

Countryside is frank that losses happen anyway: "Even experienced tanners lose a hide or two in a batch."

Are wild cottontails different from meat rabbits?

Yes. Wild cottontails have very thin, delicate skins, and hunting them brings state rules into play. Meat rabbits butchered as young fryers give thinner, lower-quality pelts. The better pelts come from adult rabbits with dense fur, taken in winter when the coat is thickest.

MSU Extension says skins from young rabbits of any breed are "normally of poor quality", and the most desirable have dense fur "that is not easily removed from the skin". Countryside adds that the coat is thickest in winter, and that rabbits raised for pelts as well as meat are often grown larger. Halford Homestead's rabbits were 12 to 14 weeks old, and he says "the younger they are the thinner they are". For hunters, Garris notes that rabbit pelts are prime in the cold winter months.

What does a small batch cost?

The chemicals for a batch of rabbit pelts cost little. Van Dyke's listed 2 pounds of ammonium alum at $11.25 and 2 pounds of aluminum sulfate at $10.25 in November 2026. Add grocery-store non-iodized salt, a lidded plastic tub, and shampoo or mink oil for finishing.

Some of the product links below are affiliate links. Taxidermy Hobbyist may earn a commission on qualifying purchases at no extra cost to you. See our affiliate disclosure.

Item (Van Dyke's, November 2026)PriceWhat the listing says
Ammonium Alum, 2 pounds$11.25Ammonium alum, 2 pounds
Aluminum Sulfate, 2 pounds$10.25Aluminum sulfate, 2 pounds
Potassium Alum Tanning Kit$29.005 pounds potassium alum and 1 pint Protal; "will tan 7 to 10 capes or hides"
McKenzie Tan Tanning Kit$26.508 oz McKenzie Tan and 8 oz Ultimate Acid; enough for two average whitetail capes
Curatan Kit, Hair On$35.00Enough for one deerskin "or the equivalent in smaller hides"

Alum is also sold as a powder, which the Cast Blast Camp video notes you can find in the baking and spice aisle: potassium alum powder. For finishing, Countryside and Souza both use mink oil. For bigger furbearers, see our guide to tanning a pelt with the fur on. For a valuable pelt you don't want to risk, ask a taxidermist near you.

Frequently asked questions

Can you tan a rabbit hide without alum?

Yes. Outdoor Life's Beka Garris soap-tanned a cottontail with olive oil and dish soap, testing a scrap in boiling water until it stayed soft. Woniya of Timeless Ways tans rabbits with an egg yolk, olive oil and castile soap dressing, then smokes them. Both need careful softening as the skin dries.

Can a tanned rabbit pelt get wet?

Expect it to stiffen. Halford Homestead says his alum-type tanned pelts "get stiff again" if they get wet. Garris notes that smoking "finishes" a hide in case it gets wet, and Souza recommends smoking for clothing or blankets. A stiff pelt can be re-wet and reworked soft.

Should you flesh a rabbit pelt before or after the soak?

Either works. Countryside and Souza soak first, because the brine loosens the membrane so it peels off by hand. Halford Homestead fleshes first with a dull knife over a beam, which he finds faster. On a cottontail, Garris scraped gently with the flat of a butter knife and then peeled the flesh.

Once your pelts are done, Countryside says never to store them in an airtight container. For what pests can do to fur, see our guide to insect damage on fur. If you'd rather mount a whole rabbit than tan a flat pelt, see our rabbit taxidermy page or the guide to mounting a small mammal.

Sources

Need a Professional?

Browse taxidermy studios, schools, suppliers and tanneries by state.

Find a Taxidermist Near You