A bass mount is either a skin mount of your actual largemouth or smallmouth, or a fiberglass replica painted to match it. Most of the price lists we read charge by the inch. On seven studio price lists that charge for bass by the inch, a skin mount runs $16 to $30 per inch and the same studios' replicas run $20 (a stated average) to $32 per inch, so at those seven a 20-inch bass works out to about $320 to $640 before minimums and bases. Studios that charge one flat price per bass ran from $300 to $1,050 on the lists we read.
How much does a bass mount cost?
At most shops, a bass mount costs a per-inch rate times the fish's length, subject to the shop's minimum. On the seven per-inch bass prices below, skin mounts run $16 to $30 per inch; replicas at the same shops run $20 (an average) to $32 per inch. Six of the seven list a higher per-inch rate for the replica than for the bass skin mount; Gunners quotes replicas per request at a stated average of $20 per inch, below its $22 bass rate.
| Studio (state) | Bass skin mount | Replica | 20-inch bass, skin (arithmetic) | Minimum |
|---|---|---|---|---|
| Jim's Taxidermy (OH) | $16/in ("Bass - Crappie") | $28/in | $320 | $150, all fish |
| Gateswood Taxidermy (AL) | $19/in | $27/in | $380 | $300 skin, $450 replica |
| Mounted Memories (MN) | $20/in | $26/in | $400 | |
| Karen's Taxidermy (AR, list dated June 2024) | $21/in (largemouth) | $28/in | $420 | |
| Gunners Taxidermy (KY) | $22/in (largemouth or smallmouth) | priced per request; stated average $20/in | $440 | |
| All Species Taxidermy (LA) | $24/in | $32/in | $480 | $225, any fish |
| Shawn's Taxidermy (MN) | $30/in (warm water, bass included) | about $32/in (stated average) | $600 | $425, warm water |
The last-but-one column is our multiplication of each published rate by 20 inches, not a quote. Ask what's included: some shops include a driftwood or panel base, others charge for habitat separately. Prices were read from each studio's own page on November 22, 2026. When you're ready, find fish mounting near me and call two or three shops.
Not every list charges by the inch. Four studios we read give one price per bass: $300 at Wildlife Reflections Taxidermy (LA, 2027 list), $350 at Jordan Lake Taxidermy (NC, 2026 list), $750 at High Country Taxidermy (NM, small base included) and $1,050 at All-American Taxidermy (IL, 2025 prices). Backwoods Taxidermy in Oklahoma prices bass by weight (see the FAQ below).
If you don't need your own fish's markings, there is a cheaper route: The Fish Mount Store sells a ready-made 19-inch smallmouth bass half mount for $230 (The Fish Mount Store). If you'd rather do it yourself, Matuska Taxidermy Supply lists a largemouth bass fish form from $26.75 and largemouth bass reproduction blanks at $127.25 to $375.95 (forms, blanks), but one beginner's 2020 supplies video put the starting kit at "around $300" (Beginners Taxidermy Guide), so the savings come after the first fish.
Should you mount the real bass or get a replica?
Get a replica if you want to release the bass. Get a skin mount if it has to be that exact fish. Either way, the paint job decides how it looks, because a bass's colors fade: as one HuntingNet angler put it, the "colors of the fish will fade fast after death" (2017).
The case for a replica: you only need photos, length and girth, and in one member's words a replica "should look good forever, the skin will not crack, and the fins will not deteriorate" (HuntingNet, 2017). Our page on replica fish mounts covers how they're made and priced.
The case against a stock replica comes from a bass: in 2012 a member wrote that his fiberglass bass "was nothing like what I caught," that "MY 10 pound bass looked like an 8 pounder," and that it cost $457, of which he got $200 back (HuntingNet, 2012). His taxidermist ordered a blank from the specs and painted it. If the shape of your fish matters, ask for a custom cast or a skin mount. In a 2017 thread, another member's view on freshwater fish was simply "For fresh, definitely a skin mount" (thread).
How is a largemouth bass replica made?
A stock largemouth bass replica is built from a purchased fiberglass blank: the taxidermist fits a mouth insert and eyes, attaches the fins, primes it, and paints it in layers. Kevin Stenzel, who describes himself as a retired fish taxidermist with over 50 years of experience, filmed the job on his wife's 10-pound 11-ounce largemouth in one preparation video and a two-part painting series:
- Prepare the purchased blank.
- Install the mouth insert, then the mouth foam, and fit the eye.
- Set the glass eye.
- Attach and blend the fins.
- Do the final detailing and prime.
- Paint: antiquing and a lacquer base, scale detail, body shading and pearls, candy colors, blending, fins, more scale detail and final detailing.
Steps 1 to 5 are the chapters of his replica preparation video; step 6 is the chapter list of part 1 of his painting series.
How is a bass skin mount made?
A bass skin mount is made by skinning the fish, removing all the meat, fitting the skin over a carved or bought foam body, pinning the fins in place, and painting it. A self-taught hobbyist's 2020 beginner bass video traces the fish on cardboard first and uses that outline to carve the body. Another home video shows the finished bass attached to driftwood (WorldClassOutdoors). If you want to try it, our guide on how to mount a bass yourself lists each step and the supplies with prices.
How do you keep a bass for the taxidermist?
Photograph and measure the bass right away, keep it whole and ungutted, and freeze it the way your taxidermist asks. Bass Pro Shops' Wildlife Creations studio says not to put a fish you want mounted on a stringer or in a wire basket, not to gut it, and to freeze it whole within 6 hours (field care sheet). Van Dyke's says to record the total length and the girth around the belly (Van Dyke's).
Sources disagree on the wrap: Van Dyke's Taxidermy Supply says wet towel and plastic bag, Bass Pro's studio says never a wet towel. Our step-by-step on how to keep the bass for the taxidermist shows each method and who recommends it.
What makes a bass mount look right?
A good bass mount gets three things right: the body shape matches the fish, the fins are set naturally, and the paint matches your photos. Shape comes from the form or blank: the 10-pound bass above was a stock blank ordered from measurements, and its owner said it looked like an 8 pounder. Paint is the rest. One AfricaHunting member wrote that "Nothing is more disappointing than an unnatural 'paint by the numbers' PAINTED over fish mount" (2023).
So before you hand over a deposit, ask to see largemouth or smallmouth bass the shop has finished, compare them with photos of live bass, and bring your own photos taken the moment the fish came out of the water. For a wider look at fishing taxidermy across species, see our fish guide.
Frequently asked questions
Does a smallmouth bass mount cost the same as a largemouth?
Usually. Gunners Taxidermy in Kentucky lists "Largemouth/Smallmouth Bass" on one line at $22 per inch, and most other studios we checked price bass as one line without splitting the two. Ask if your shop treats a big smallmouth differently.
Is a bass mount priced by weight or by length?
Usually by length. Every studio in the table above charges per inch, and one other studio we checked adds a flat fee on top: Vance Wildlife Taxidermy in Virginia charges $100 plus $15.50 per inch for freshwater fish like bass. One studio we checked prices bass by weight instead: Backwoods Taxidermy in Oklahoma lists largemouth and smallmouth bass at $395 for 1 to 4 lbs. up to $595 for 11 to 13 lbs. Ask your shop which way it charges.
How much is a 10-pound bass replica?
It depends on its length and the shop's rate. One HuntingNet member reported paying $457 for a 10-pound bass replica in 2012, and got $200 back after it came out looking smaller than his fish. At today's published rates, multiply the fish's length in inches by the shop's replica rate, then check the minimum.
Can I mount a bass I caught years ago and kept in the freezer?
Possibly, but ask first. Bass Pro's Wildlife Creations studio warns that too long in the freezer can damage the fish and recommends mounting within 3 months of the catch. If the fish is past saving, a replica made from your photos and measurements is the fallback.