GuidesBy Taxidermy Hobbyist Editorial TeamUpdated November 22, 2026

How to Hang a Heavy Mount Safely

To hang a deer mount, find the hanger on the back of the mount, find a stud where you want it, drive a screw into that stud and hang the mount on it, then level the eyes. No stud? A heavy-duty toggle anchor, a board spanning two studs, or blocking behind the drywall does the job. This guide covers each fix, how high and at what angle to hang, European mounts, and fitting big mounts under a low ceiling. The advice comes from hunters on Rokslide and AfricaHunting, taxidermy videos and an anchor maker's test data.

How do you hang a deer mount on the wall?

Screw into a stud and hang the mount's back hanger on that screw. Then nudge the mount until it sits square and the eyes are level. Where the hanger sits differs on every mount, so measure your own mount before you drill, not a friend's.

  1. Look at the hanger first. A Rokslide member answering a hunter planning blocking for a moose said the distance from the top of the mount or the brisket to the hanger "varies on every single mount", because the taxidermist decides where it goes (2021). Another reply there said hangers are centered to suit the form so the mount does not rotate.
  2. Find the stud. One AfricaHunting member with a house full of taxidermy uses only his existing studs: he finds both outer edges of the stud with a stud finder and drives a large-headed screw at a downward angle (2021).
  3. Hang it and level the eyes. Rodney Elmer, a taxidermist of almost 40 years, calls the traditional back hanger an industry standard, and says in his video that you always have to shift the mount a little to make it sit where you want and level the eyes (Mountain Deer, 2025).

How do you find a stud where you want the mount?

Run a stud finder across the wall and mark both edges of the stud, then drive the screw through the middle. If the nearest stud is off center from where the mount should go, use one of the no-stud fixes below rather than hanging the mount crooked.

The Rokslide member who started a 2025 no-stud thread had his closest stud about 8 inches off center from where his wife wanted an elk skull (2025). One AfricaHunting member paid an art-hanging company to confirm the studs he had found before his four-foot-deep buffalo went up (2017).

Some of the product links below are affiliate links. Taxidermy Hobbyist may earn a commission on qualifying purchases at no extra cost to you. See our affiliate disclosure.

Any stud finder does the job; mark the edges in pencil where the mount will hide them.

What holds a mount when there is no stud?

Heavy-duty toggle bolts come up again and again in a Rokslide no-stud thread, and the maker's published test numbers back it for drywall. Size the anchor to a quarter of its tested load, and remember the maker says it holds less the farther the load sits from the wall.

Toggler's SNAPTOGGLE product page says the anchor holds up to 238 pounds in half-inch drywall. Its technical flyer shows where that number comes from: 238 pounds is the ultimate tensile pull-out value for the 3/16 inch BA size in 1/2 inch drywall, with 247 pounds ultimate shear. The same flyer adds two cautions: "Industry standards recommend 1/4 of ultimate test load," and holding strength drops with "the distance of the load from the wall" (SNAPTOGGLE flyer, page 3). A quarter of 238 pounds is about 60 pounds per anchor. The flyer lists plaster and gypsum board among the walls it works in.

The distance point comes up on the forums too. A Rokslide member put it simply in 2026: "The weight rating for the anchor is the force pulling down." Another said a toggle in standard 1/2 inch drywall should be fine for a European mount, but that a big full mount whose weight sits far out from the wall could be a bigger problem (2025).

What hunters report using without a stud:

  • Toggle anchors: recommended by several members in a Rokslide thread (2025 to 2026), including one who hung a 5x5 elk European mount that way (2026).
  • Screw-in drywall anchors: one member has had several deer shoulder mounts on metal screw-in anchors for more than 20 years (2026). A home builder on AfricaHunting said his 6x6 elk mount had hung for 12 years on a single screw-in drywall anchor (2021).

If you go the toggle route, compare SNAPTOGGLE toggle bolts and check the size against the maker's table before you drill.

How heavy is the mount? No maker publishes a weight for your mount, so weigh it if you can. Forum figures give a sense of scale: one Rokslide member put a 300 inch 6x6 elk European mount at around 20 pounds (2025), and later found a seller listing a 358 inch bull, wood plaque included, at 42 pounds (2026).

How do you hang a mount between two studs?

Fasten a board across two studs, then hang the mount from the board instead of the wall. The board carries the load to both studs, so the mount can hang anywhere along it, centered where you want it, even when neither stud is.

One Rokslide member built a wood frame that spanned 16 inches and hung his European mount from that (2025). Others in the same thread built on the idea: a small wood plaque to spread the weight and catch at least one stud; a piece of decorative wood long enough to reach 16 inches, predrilled and fixed with long lag screws; and a piece of plywood sized to hide behind the skull, painted the wall color and held with two or three toggle anchors, with a wood screw into the plywood for the mount (2025).

Should you add blocking or plywood behind the drywall?

For a heavy mount on an existing wall, open the drywall and screw a horizontal 2x4 or 2x6 between two studs at hanging height, then patch. In a new build, back the whole trophy wall with plywood or OSB so a mount can go anywhere.

Existing wall. One Rokslide member with an elk European mount over a stairwell opened a square of drywall over the stud on each side, fitted a horizontal brace between them at hanging height, then screwed the drywall back, taped, mudded and painted before screwing the mount straight into the brace (2025). Another suggested running a 2x4 or 2x6 between the studs and patching the drywall (2025).

New build or remodel. On AfricaHunting, a long-time contractor advised 5/8 or 3/4 inch OSB screwed to the studs with drywall over it, plus 2x blocking between studs at likely heights for extra insurance (2021). A Rokslide member put 3/4 inch plywood behind his drywall from 3 feet off the floor to the ceiling so he can hang virtually anything in any spot (2026). Photograph any blocking before the drywall goes on so you can find it later.

How high should you hang a deer mount?

There is no fixed height. The forum answers range from face at eye level to as high as the ceiling allows. Hold the mount up, step back, and move it until it looks right before you drill.

In a 2025 AfricaHunting thread on mounting height, one member said to go as high as you can without the horns touching the ceiling, maybe 3 inches below that. Another puts the bottom of the mount at the top of your head, so the mount is out of the way but you still see the face. With 9-foot ceilings, one member keeps tall-horned animals about 6 inches below the ceiling and the eyes a little above his own, because he wants people to see the face, not the throat and chin. The member who asked hung his with the face and nose bridge at eye level.

One member's tip in that thread: have someone hold the mount in place while you step back, and adjust it before any anchor goes in. He once stuck life-size cardboard cutouts of his mounts to the walls before drilling, and he weighs traffic: tall visitors who might hit a nose, and people who touch mounts.

Which way should the mount face, and how much should it tilt?

Turn the mount to face the door or the middle of the room. The tilt is set by the form your taxidermist chooses, so decide on the pose with the wall in mind: an upright head needs more room above it than a sneak pose.

Mike Travis of Upper Bay Taxidermy in Maryland says in his video on mount styles that you always want the deer "turned towards the doorway or the center of the room" (2013). Nikki Carter, in a McKenzie Taxidermy Supply video, likes the deer to face the viewer walking in, and warns that with an upright or semi-upright pose the antlers need space above them so they don't hit the ceiling (2012). See our deer mount poses guide.

Rodney Elmer adds a moisture point for outside walls: a mount pressed flat against a poorly insulated exterior wall can collect moisture on its back, which can lead to mold and moths, so airflow behind the mount helps. His video promotes a swivel bracket that holds the mount off the wall; the description links a store that sells it. And a reply in a Rokslide thread warned against hanging a mount above a wood burning fireplace (2021).

How do you hang a European mount?

Hunters in the Rokslide no-stud thread hang European mounts on skull hangers screwed into drywall anchors and report them holding. For a big elk skull, several in that thread chose a toggle bolt or a board or brace across two studs instead.

One Rokslide member has three Skull Hooker brackets in drywall, each on two screws and anchors, and calls them solid even with the weight 8 to 10 inches off the wall (2025). Another hooks a skull hanger onto drywall anchors in the 50 to 75 pound range (2025). Our Skull Hooker review compares the bracket sizes, and you can browse Skull Hooker hangers on Amazon.

Will a big mount fit your wall and ceiling?

Measure depth as well as height. Several hunters report buffalo shoulder mounts about four feet from wall to nose. Under a low ceiling, the head's tilt, a sneak pose, a lower pedestal base or a European mount make the difference.

Depth. In a 2017 thread on buffalo shoulder mounts, three members reported theirs at about four feet from the wall (one, two, three); a buffalo skull mount was about 16 inches deep. Another member put a kudu, gemsbok or waterbuck shoulder mount at about 3 to 4 feet out, and his eland at about 52 inches (2018).

Height. On AfricaHunting, one member's kudu with 55 inch horns, a pedestal mount, lived in a six-foot basement alcove, and his explanation was "It is all in the tilt of the head." (2024). For that basement he had told his taxidermist to keep the horn tips below 6 feet 11 inches (2018). Another member in that 2018 thread said full sneak or semi-sneak poses help with ceiling clearance. A 2024 reply summed up the two levers for a pedestal: the head angle and the height of the base.

Some members prefer pedestal mounts because they can be moved (2024); see our pedestal mount guide. Bring your ceiling height and wall depth when you find a taxidermist, before the form is chosen. For styles, see mount types explained; for upkeep, our taxidermy care guide; for a whole room, trophy room ideas.

Frequently asked questions

Can drywall anchors hold a deer shoulder mount?

Plenty of forum members report it working. One Rokslide member has had several deer shoulder mounts on metal screw-in anchors for over 20 years. Toggler rates its SNAPTOGGLE BA at 238 pounds ultimate pull-out in 1/2 inch drywall and notes that industry standards recommend a quarter of the ultimate test load, with holding strength falling as the load moves out from the wall.

Can you hang a mount on a plaster wall?

Toggler's flyer lists plaster among the walls its SNAPTOGGLE works in. Where you can reach a stud, or put a board across two studs, that hold doesn't depend on the plaster at all.

How far out from the wall does a shoulder mount stick?

It depends on the animal and pose. AfricaHunting members reported buffalo shoulder mounts at about four feet and an eland at about 52 inches; a buffalo skull mount was about 16 inches deep.

Need a Professional?

Browse taxidermy studios, schools, suppliers and tanneries by state.

Find a Taxidermist Near You